Nutanix AOS 5.5 delivers 1M read IOPS from a single VM, but what about 70/30 read/write?

I recently wrote Nutanix AOS 5.5 delivers 1M IOPS from a single VM, but what happens when you vMotion which showed the impact of a vMotion was around -10% for a period of approx. 3 seconds before read performance resumed back to pre-migration levels.

In this post I will be addressing the question about performance for a single VM with a more realistic 70% read, 30% write IO profile which was performed using an 8k IO size and what the impact is during and after a live migration.

While not surprising to Nutanix customers, this result shows a maximum starting baseline of 436K random read and 187k random write IOPS and immediately following the migration performance reduced to 359k read and 164k write IOPS before achieving greater performance than the original baseline @ 446k read and 192k IOPS within a few seconds.

So in comparison to 100% random read which achieved just over 1 million 8k IOPS, the 70/30 mix achieves in the ballpark of 600k IOPS which is very respectable. Not bad for a platform which Nutanix competitors continue to describe as only being good for VDI. Considering even the largest array from a leading all flash SAN vendor is only advertising performance in the hundreds of thousand random read range, it shows Nutanix unique hyper-converged architecture can achieve higher performance than a monolithic all flash array from a single VM.

This shows that with the unique Nutanix Acropolis Distributed Storage Fabric, very high performance at low latency can be achieved with real world IO patterns even during and after live migrating the virtual machine across a distributed platform.

This result is further evidence of the efficiency of Nutanix Acropolis Hypervisor, AHV (which is included at no additional charge with AOS) as well as the IO path running in user space (not the much hyped in-kernel). This is in part thanks to AHV Turbo Mode which optimised the IO path which was announced at .NEXT 2017 in Washington. In addition to these excellent levels of performance, they can be sustained even when using data protection features such as snapshots as shown in recent post I wrote about Nutanix X-ray tool where I used the Snapshot impact scenario to compare Nutanix AHV and a leading hypervisor and SDS product. If you don’t have time to read the post, in short, the Nutanix competitors performance degraded as snapshots were taken while Nutanix AHV’s performance remained consistent which is essential for real world scenarios, especially with business critical applications.

With Nutanix unique ability to scale out performance using storage only nodes, even higher performance can be achieved without modification to the virtual machine to applications which gives Nutanix further advantage over the competition.

Nutanix data locality ensures optimal performance by ensuring new data is always local to the VM and cold data can remain remote indefinitely while only hot data will be migrated locally if/when required at a 1MB granularity. This translates to intelligent data locality and not brute force locality as it is frequently mistaken to be.

Back to Part 1

Scale out performance testing with Nutanix Storage Only Nodes

At Nutanix inaugural user conference in 2015, Storage Only nodes were announced which allowed customers for the first time to scale capacity without having to add compute nodes. This allows customers more flexibility and eliminates the need to license the storage nodes for vSphere as storage only nodes run Acropolis Hypervisor (AHV) and are managed entirely through PRISM.

A common question from prospective and existing Nutanix customers is what if my VMs storage exceeds the capacity of a Nutanix node? The answer is detailed in this blog post but in short, as the Acropolis Distributed Storage Fabric (ADSF) distributes data throughout the cluster at a 1MB granularity, a VMs storage can exceed the local node and performance even improves including reads from the capacity (SAS/SATA) tier.

Storage only nodes were previously limited to the NX-6035C (and Dell XC/Lenovo HX equivalents) but at Nutanix .NEXT conference in Las Vegas 2016, it was announced that any node (including all-flash) can be a storage only node.

This means even for high performance and/or high capacity environments, Nutanix clusters can be scaled without the need to add compute node or purchase additional licensing if you are running vSphere as the hypervisor.

However to date Nutanix are yet to publish any performance data showing the value of storage only nodes, so I decided to run a few tests and demonstrate the value of the Acropolis Distributed Storage Fabric (ADSF) and Storage Only Nodes.

Before we get to the performance data, to avoid competitors inevitable attempts to create FUD about Nutanix performance, I will not be publishing the exact specifications of the node types, drive or Jetstress configurations. I will be publishing the IOPS/latency and database creation, duplication and checksumming durations of the direct comparisons which clearly show the performance advantage of storage only nodes.

Jetstress was not configured to demonstrate maximum performance of the underlying Nutanix solution, it was configured to achieve around 1000 IOPS which is typically higher than even a large Exchange deployment requires per instance. This also allows this test to demonstrate how performance improves when the cluster is performing real world levels of IO (at least in the case of Exchange for this example).

The performance advantage will vary between node types and based on how many storage only nodes are added to the cluster. But the point of this example is to show that ADSF is a truely distributed storage fabric and the storage only nodes and additional Nutanix Controller VMs (CVMs) servicing replication (RF) traffic and remote reads significantly improves performance for VMs residing on the Compute+Storage nodes.

Test Overview:

The first test will be performed using four Jetstress VMs running on a four node cluster. The second test will be performed after an additional four storage only nodes are added to the cluster to form an eight node cluster. Before the second test the cluster will be wiped of all data with the exception of the Windows 2012 R2 template and all Jetstress DBs will be created from scratch so we can compare DB creation as well as performance and DB checksumming durations. Wiping all data also ensures there is no pre-warming of the extent cache (in memory read cache) or metadata cache.

Test Preparation:

I performed a cluster stop / cluster destroy / cluster create to ensure the cluster is totally clean and that we have a fair baseline for the test. The cluster was made up of four nodes.

I then created a base Windows 2012 R2 virtual machine with 4 PVSCSI adapters and 9 vDisks, one for the OS, 4 for the DBs and 4 for the logs. DB drives were formatted with 64k allocation size and log drives with 4k as the different allocation size and seperate virtual disks has shown approx 25% performance improvement in my testing not to mention I recommend In-Line compression and Erasure Coding (EC-X) for Exchange databases and no data reduction for logs.

Jetstress was configured to use 80% of the vDisks capacity which resulted in approx 80% of the Nutanix storage pool capacity being utilised for the test. I will point out these were not low capacity nodes such as NX3060s so the database creation time is significant because there was lots of data to create.

I then cloned the VM 3 times and spread the 4 VMs across 4 Nutanix Nodes running ESXi 5.5 Update 3.

Test 1: Create Databases and run 2hr test

The databases creation phase creates one database, then Jetstress duplicates the database in this case 3 times and immediately after creation the performance test begins.

Note: No data reduction was used for this test as it will result in unrealistic data reduction and performance results as I described in the post Jetstress Testing with Intelligent Tiered Storage Platforms.

I configured Jetstress in this way to ensure the extent cache (in memory read cache) was not pre-warmed and so the results of the test would be fair and repeatable.

Once the performance test completed, I waited for each test to complete before allowing the database checksum validation task to complete. (This is done by using the Multi-host option in Jetstress).

The results for each of the four Jetstress VMs are shown below including the average across the VMs for each of the difference metrics.

Jetstress4NodesSummary

Observations from Test 1:

  1. We achieved the desired >1000 IOPS per VM
  2. Performance was consistent across all Jetstress instances
  3. Log writes were in the 1ms range as they were serviced by the ADSF Oplog (persistent write buffer)
  4. Database reads were on average just under 10ms which is well below the Microsoft recommended 20ms
  5. The Database creation time averaged 2hrs 24mins
  6. The duplication of 3 databases averaged 4hrs 17mins
  7. The database checksum took on average around 38mins

Test 2: Delete all data, Add four nodes to the cluster & repeat test 1

All Jetstress VMs were deleted and a full curator scan manually initiated to ensure all data was fully removed from disk prior to beginning the next test which ensured a fair baseline.

Four Jetstress VMs were then deployed from the same template, powered on and the saved Jetstress configuration was applied before beginning the test.

Note: The Jetstress thread count was not changed and remains the same as for Test 1.

As with Test 1 the databases creation phase created one database, then Jetstress duplicates the database 3 times and immediately after creation the performance test begins and ran for the same 2hr duration.

The results for each of the four Jetstress VMs are shown below including the average across the VMs for each of the difference metrics.

Jetstress8NodesSummary

Observations from Test 2:

  1. Achieved IOPS jumped by almost 2x
  2. Log writes average latency was lower by 13%
  3. Database write latency dropped by >20%
  4. Database read latency dropped by almost 2x
  5. The Database creation time was just under 15 mins faster
  6. The duplication of 3 databases improved by almost 35 mins
  7. The database checksum was 40 seconds faster.

Without changing the Jetstress thread count, due to the improved performance of the cluster the achieved IOPS jumped by 2x!!

Summary:

These tests is a clear demonstration of the scalability advantage of the Acropolis Distributed Storage Fabric (ADSF) and storage only nodes for customers wanting to increase performance and/or capacity in their HCI environment.

The ability of ADSF to distribute write IO across all nodes within a cluster means write performance improves significantly with the addition of nodes (including storage only) to the cluster while reducing read and write latency due to the decreased workload on the compute + storage nodes servicing the VMs.

But data locality is lost with storage only nodes, right?

Wrong! Storage only nodes actually improve (yes, improve!) data locality by maximising the amount of available space on the compute+storage nodes. This is as a direct result of storage only nodes accepting replication data for write IO and storing the 2nd or 3rd copies (in the case of RF3) on the storage only nodes. This is also demonstrated by the lower read latency observed during this test.

Storage only nodes not only improve the performance and capacity for Virtual machines, but also for physical servers using Acropolis Block Services (ABS) and users of Acropolis File Services (AFS) both of which had enhancements announced at .NEXT 2016 this year.

NOS 4.5 Delivers Increased Read Performance from SATA

In a recent post I discussed how NOS 4.5 increases the effective SSD tier capacity by performing up-migrations on only the local extent as opposed to both RF copies within the Nutanix cluster. In addition to this significant improvement in usable SSD tier, in NOS 4.5 the read performance from the SATA tier has also received lots of attention from Nutanix engineers.

What the Solutions and Performance Engineering team have discovered and been testing is how we can improve SATA performance. Now ideally the active working set for VMs will fit within the SSD tier, and the changes discussed in my previous post dramatically improve the chances of that active working set fitting within the SSD tier.

But there are situation when reads to cold data still need to be serviced by the slow SATA drives. Nutanix uses Data Locality to ensure the hot data remains close to the application to deliver the lowest latency and overheads which improve performance, but in the case of SATA drives and the fact data is infrequently accessed from SATA means that reading from remote SATA drives can improve performance especially where the number of local SATA drives is limited (in some cases to only 2 or 4 drives).

Most Nutanix nodes have 2 x SSD and 4 x SATA so best case you will only see a few hundred IOPS from SATA as that is all they are physically capable of. To get around this issue.

NOS 4.5 introduces some changes to the way in which we select a replica to read an egroup from the HDD tier. Periodically NOS (re)calculate the average IO latencies of the all the replicas of a vdisk’s (replicas which have the vdisk’s egroups). We use this information to choose a replica as follows:

  1. If the latency of the local replica is less than a configurable threshold, read from the local replica.
  2. If the latency of the local replica is more than a configurable threshold, and the latency of the remote replica is more than that of the local replica, prefer the local replica.
  3. If the latency of the local replica is more than a configurable threshold and the remote replica is lower than the configurable threshold OR lower than the local copy, prefer the remote replica.

The diagram below shows an example of where the VM on Node A is performing random reads to data A and shortly thereafter data C. When requesting reads from data A the latency is below the threshold but when it requests data C, NOS detects that the latency of the local copy is higher than the remote copy and selects the remote replica to read from. As the below diagram shows, one possible outcome when reading multiple pieces of data is one read is served locally and the other is serviced remotely.

remotesatareads2

Now the obvious next question is “What about Data Locality”.

Data Locality is being maintained for the hot data which resides in SSD tier because reads from SSD are faster and have lower overheads on CPU/Network etc when read locally due to the speed of SSDs. For SATA reads which are typical >5ms the SATA drive itself is the bottleneck not the network, so by distributing the Reads across more SATA drives even if they are not local, results in better overall performance and lower latency.

Now if the SSD tier has not reached 75% all data will be within the SSD tier and will be served locally, the above feature is for situations where the SSD tier is 75% full and data is being tiered to SATA tier AND random reads are occurring to cold data OR data which will not fit in the SSD tier such as very large databases.

In addition NOS 4.5 detects if the read I/O is random or sequential, and if its sequential (which SATA performance much better at) then the up-migration of data has a higher threshold to meet before being migrated to SSD.

The result of these algorithm improvements (and the increased SSD tier effective capacity discussed earlier) and Nutanix In-line compression is higher performance over larger working sets which also exceed the capacity of the SSD tier.

Effectively NOS 4.5 is delivering a truly scale out solution for read I/O from SATA tier which means one VM can be reading from potentially all nodes in the cluster ensuring SATA performance for things like Business Critical Applications is both high and consistent. Combine that with NX-6035C storage only nodes, this means SATA read I/O can be scaled out as shown in the below diagram without scaling compute.

ScaleOutRemoteReads

 

As we can see above, the Storage only Nodes (NX-6035C) are delivering additional performance for read I/O from the SATA tier (as well as from the SSD tier).