Tag Archives: vcap

Competition Example Architectural Decision Entry 2 – Use of RDMs in Standard IaaS Clusters

Posted on by
Reply

Name: Chris Jones
Title: Virtualization Architect
Twitter: @cpjones44
Profile: VCP5 / VCAP5-DCD

Problem Statement

VMs require more than 1.9TB in a single disk. The existing virtual environment has LUNs provisioned that are 2TB in size. As these VMs have virtual data disks (VMDKs) that are > 1.9TB in size, alarms are being triggered by the infrastructure monitoring solution and raising Incident tickets to the Virtual Infrastructure support queue.

Assumptions

1. Data within the OSI must reside within the VM and not on some kind of IP based store (like a NAS share).

2. vSphere datastores are presented through FC and not IP based stores (ie. NFS).

3. vSphere Hypervisor is ESXi 4.1.

4. There is no requirement for the VMs to be performing SAN specific functionality or running SCSI target-based software.

Constraints

1. The implemented monitoring solution cannot be customised with triggers and monitoring policies for individual objects within the environment (ie. having one monitoring policy per individual or sub-group of datastores).

2. Maximum vSphere datastore size in version 4.1 is 2TB minus 512 bytes.

3. Unable to upgrade beyond ESXi 4.1 Update 3.

Motivation

1. Reduce the number of incident tickets being raised, thus improving SLA posture.

2. Reduce the requirement to span single Windows logical volumes across multiple VMDKs.

Architectural Decision

Turn the disk into an RDM (Virtual Compatibility Mode) to remove the level of monitoring from the vSphere layer.

Alternatives

1. Create smaller VMDKs (ie. 1-1.5TB disks) and create a RAID0 volume within the guest OS.

2. Change the level of alerting so that tickets are not raised for alerts that trigger beyond 90%.

3. Turn the disk into an RDM to remove the level of monitoring from the vSphere layer.

4. Thin Provision the virtual disks

5. Store the data within the guest on some kind of IP based storage (NAS/iSCSI target).

Justification

1. Option 5 goes against the assumption that data must be local to the VM, so was ruled out.

2. Whilst thin provisioning (Option 4) is an attractive solution, this option is ruled out based on a wider infrastructure decision to thick provision all disks in the environment to reduce the risk to datastores filling up and critical business VMs stopping.

3. Option 1 via smaller VMDKs spread across multiple vSphere datastores will result in these alerts disappearing, however it will create issues when trying to execute a DR recovery for either the individual disks (Active/Passive) or the whole VM (Active/Cold). All that’s needed is for one VMDK not to be replicated and the whole Windows volume will be corrupted, or for the VMDKs to be mounted in the wrong order. Multiple VMDKs to one Windows volume also complicates the recovery of snapshot array-based backups (eg. via SMVI or NetBackup).

4. Option 2 goes against the constraint of the infrastructure monitoring solution not being able to creating individual alerting policies for either a single or sub-group of datastores in the inventory. Should individualised policies be created, we would need to ensure that the affected VMDKs that consume 90-95% of a datastore remain on that datastore as moving from one to another (ie. from Tier 2 to Tier 1) will require a change to the monitoring that has been configured. At this stage, the monitoring solution has no way to track these customised policies, which is most of the reason why global environment wide policies exist.

5. Option 3 and the use of RDMs in Virtual Compatibility Mode will allow the VM to benefit from the features of VMFS, such as advanced file locking for data protection and vSphere snapshotting. The use of RDMs will also allow for VMs to be managed by DRS (ie. can be vMotion’ed) and protected by vSphere HA.

Implications

  1. The RDM mapping will need to be recorded clearly to avoid the lengthy process of discovering from scratch what physical LUN is presented to the virtual machine.

An example of how to map these will be to:

A)    Record the name of the VM that has the RDM.

B)    Record the NAA number of the physical LUN(s) that are presented to the VM.

C)    Record the virtual device node on the virtual disk controller as to where the RDM is mounted.

D)    Record the Windows drive letter that this RDM is mounted to.

2. Additional paths will be consumed, reducing the total number of vSphere datastores that can be presented to the cluster.

Back to Competition Main Page or Competition Submissions

Data Centre Migration Strategies – Part 2 – Lift and Shift

Posted on by
2

Continuing on from Data Centre Migration Strategies Part 1 – Overview, Part 2 focuses on the “Lift and Shift” method.

I’m sure your reading this and already thinking, “this is the least interesting migration strategy, tell me about vMSC and SRM!” and well, your right, BUT it is important to understand the pros and cons so if you are ever in a situation where you have to use this method (I have on numerous occasions) that the migration is successful.

So what are the pros and cons of this method.

Pros

1. No need to purchase equipment for the new data centre
2. The environment should perform as it did at the original data centre following relocation
3.The approach is simple from a technical perspective ie: No new products are required
4. Low direct cost (Note: Point 8 in Cons)
5. Achieves a Recovery Point Objective (RPO) of zero (0).

Cons

1. The entire environment needs to be fully shut-down
2. The outage for the environment starts from when the servers are shut-down, until completion of operational verification testing at the new datacenter. Note: This may take several days depending on the size of the environment.
3. This method is high risk as the ability to fail back to the original datacenter requires all equipment be physically relocated back. This means the Recovery Time Objective (RTO) cannot be low.
4. The Lift and shift method cannot be tested until at least a significant amount of equipment has been physical relocated
5. In the event of an issue during operational verification at the new data centre, a decision needs to be made to proceed and troubleshoot the issues, OR at what point to fail back.
6. Depending on your environment, a vendor (eg: Storage) may need to revalidate your environment
7. Your migration (and schedule) are heavily dependant on the logistical side of the relocation which may have many factors (eg: Traffic / Weather) which are outside your control which may lead to delays or failed migration.
8. Potentially high indirect cost eg: Downtime, Loss of Business , productivity etc

When to use this method?

1. When purchasing equipment for the new data centre is not possible
2. When extended outages to the environment are acceptable
3. When you have no other options

Recommendations when using “Lift and Shift”

1. Ensure you have accurate wiring and rack diagrams of your datacenter
2. Be prepared with your vendor support contact details on hand as it is common following relocation of equipment to have hardware failures
3. Ensure you have an accurate Operational Verification document which tests every part of your environment from Layer 1 (Physical) all the way to Layer 7 (Application)
4. Label EVERYTHING as you disconnect it at the original datacenter
5. Prior to starting your data centre  migration, discuss and agree on a timeline for the migration and at what point and under what situation do you initiate a fail back.
6. Migrate the minimum amount of physical equipment that is required to get your environment back on-line and do your Operational Verification, then on successful completion of your Operational Verification migrate the remaining equipment. This allows for faster fail-back in the event Operational Verification fails.

In Part 3, we discuss Data centre migrations using VMware Site Recovery Manager. (Coming soon)

 

VMware Certified Associate – Data Center Virtualization , Cloud and Workforce Mobility

Posted on by
72

Recently VMware has launched 3 new certifications aimed at the foundation layer to demonstrate your fundamental understanding of VMware technology in three key areas, being Datacenter Virtualization, Cloud and Workforce Mobility.

The good news is, these exams can be registered for, and taken online, and if your willing to sit the exams before the end of October 2013 Jan 2014, you can use the below voucher to sit all 3 exams for 50% off!

50% off Voucher

1. VCA13GKN

If the voucher does not work for any reason unfortunately there is nothing I can do to assist.

VMware Certified Associate – VCAC510 – Cloud (VCA-Cloud)

The self-paced e-learning class can be found here and taken for free.

VMware Certified Associate – VCAD510 – Data Center Virtualization (VCA-DCV)

The self-paced e-learning class can be found here and taken for free.

VMware Certified Associate – VCAW510 – Workforce Mobility (VCA-WM)

The self-paced e-learning class can be found here and taken for free.

Coming soon there will also be the VMware Certified Associate – Network Virtualization (VCA-NV) for those folk who are focusing on the emerging network virtualization path with NSX (formally Nicira).

So you have nothing to loose, study the free self-paced e-learning classes, register for the exams and sit them at 50% off, in the comfort of your own home.

I sat and passed all three exams yesterday and I must congratulate VMware Education as I feel they have added a entry level certification for those people either starting in virtualization, non VMware partners (customers) who cannot access the VMware Sales Professional (VSP) or VMware Technical Sales Professional (VTSP) tracks, or for people who do not intend going down the technical certification path of VMware Certified Professional (VCP) , VMware Certified Advanced Professional (VCAP) or VMware Certified Design Expert (VCDX).

I guess for me the exams were pretty easy, but I have had many years experience including administration, implementation and architecture, so the exams are not really designed for people who have already completed, VCP or higher, but the exam questions tests general product knowledge which shows the test taker understands what VMware product helps solve what problem which is a important.

For anyone considering going down the VCP track, VCA is a great starting point and will help build your confidence to tackle the harder VCP (and beyond) exams.

Related Articles

1. My VCDX Journey  

2. The VCDX Application Process

3. My VCAP-DTD (Design Design) Experience

VCAtrifecta